Pull Out Kitchen Faucet,Black Pull Out Tap,Pull Out Kitchen Tap,Brushed Brass Kitchen Tap Heshan Jasupi Sanitary Ware , https://www.jasupifaucets.com
The aluminum alloy crystallizer, also known as the condensate tank, plays a decisive role in casting. The taper change of the aluminum alloy crystallizer cannot be ignored for casting. The crystallizer's taper is too large. The segregation of the surface of the ingot will increase when it is cast. If the operation is not good, slag inclusion will cause surface cracking. If the crystallizer is too narrow, it will produce surface crack when casting the ingot. A good casting master will adjust the size of the crystallizer at any time to prevent surface cracks in the slab casting.
Surface cracks in aluminum alloy slabs are also critical for cooling water. Whether the cooling water is evenly distributed or not, the strength of the large and small surfaces, the size of the blisters, and the water temperature all have a great influence on the solid-liquid region. Case 2. There was a surface crack often occurred in a aluminum company when it had just made slabs. There was no analysis of the causes and a great deal of waste was caused. One of my colleagues visited the factory and discovered the problem. Because the water temperature was too high, it was adopted. Chemical and physical methods of action solve the problem of surface cracks. Case 3: Some companies use the water in the fish pond as cooling water, and the surface of the aluminum alloy ingot is blocked by the suspended solids that cause excessive pores.
The aluminum alloy crystallizer, also known as the condensate tank, plays a decisive role in casting. The taper change of the aluminum alloy crystallizer cannot be ignored for casting. The crystallizer's taper is too large. The segregation of the surface of the ingot will increase when it is cast. If the operation is not good, slag inclusion will cause surface cracking. If the crystallizer is too narrow, it will produce surface crack when casting the ingot. A good casting master will adjust the size of the crystallizer at any time to prevent surface cracks in the slab casting.
The aluminum alloy crystallizer, also known as the condensate tank, plays a decisive role in casting. The taper change of the aluminum alloy crystallizer cannot be ignored for casting. The crystallizer's taper is too large. The segregation of the surface of the ingot will increase when it is cast. If the operation is not good, slag inclusion will cause surface cracking. If the crystallizer is too narrow, it will produce surface crack when casting the ingot. A good casting master will adjust the size of the crystallizer at any time to prevent surface cracks in the slab casting.
In summary, the surface cracks of the aluminum alloy slabs are one of the common defects in the casting process. Eight analysis reasons should be taken into account during the casting process. Failure to follow every detail can lead to errors and losses. Alloy composition. Impurity control problems and process settings need to be analyzed and analyzed according to different environments to make accurate judgments. For example, the slag on the surface of an aluminum alloy slab is one of the most common surface cracks caused by the casting operation. Most of them are caused by improper operation, such as the control of the furnace temperature - water pressure - speed - whether the flow tray horn is flat - the level of the crystallizer level - operation, etc., exists in every detail. In order to prevent the occurrence of surface cracks in aluminum alloy slabs. This is true for everything from semi-continuous casting to fully automatic casting. For example, the internal quality defect in fully automatic casting is a new topic. For example: feathered crystals, columnar crystals, vertical trees, and the production and prevention of bright crystal columns, we will continue research and discussion.
The casting surface cracks of aluminum alloy slabs are a common problem. The key to solving this problem is to consider three main aspects: 1) Control of the chemical composition of the alloy. 2 is the casting process of alloy varieties. 3 is operational skills and natural conditions. The surface cracks that occur in the semi-continuous casting of aluminum alloys should take into account many factors: 1 mold taper; 2 casting temperature; 3 slag inclusion during casting; 4 melt overheating; 5 too rapid casting speed; 6 cooling system; 7 alloy chemistry Ingredients; 8 Operational skills; Case 1 An aluminum company, in the production of 5052 alloy slabs, resulting in surface cracks in the three furnace ingot, and are in the same position, resulting in companies forced to temporarily stop production. After we watched the company's delivery of the video, we found a small problem with a small amount of yellow dry oil on the back of the mold. Causes cooling water flow, resulting in surface cracks in aluminum alloy slabs.